This website uses cookies to optimize your user experience. By navigating on this website, you consent to this use. To find out more about cookies, consult our privacy policy.
TRANS-SPACE

TRANS-SPACE

Strong and Reliable Body

Specifications

Volume

18 → 26

Axle(s)

Double axle
Triple axle

Range

Monocoque Tipping Trailers

TRANS-SPACE General Points

General Points

Thanks to its design and manufacturing quality, the empty weight of the Trans-Space agricultural tipping trailers is significantly reduced and therefore allows to transport still higher payloads. Combined to a JOSKIN running gear, they are ideal for intensive transport.

TRANS-SPACE Hitching

Hitching

The "girder" drawbar was tested to withstand the highest loads and intensive works.

TRANS-SPACE Concept

Concept

The Trans-SPACE are made of a floor sheet in HARDOX and two side sheets (four on the Trans-SPACE 8000) in high tensile steel. The underside of the Trans-SPACE is meant for the most constraining works: two opposing stringers support the body with unmatched stability. The first rather big one links both side reinforcements to each other while the other is placed at the level of the anchoring point of the hydraulic tipping ram.

Strong points of the range

Tipping

The tipping system is standard oil fed. There is an option that makes it possible to replace it by a hydraulic pump, which may be fitted with a hydraulic or electric lowering control.

Door: tight and safe

Monocoque tipping trailers are fitted with very resistant synthetic rubber seals all around the body. The door is kept closed by a side locking device (except on vehicles with drop sides).

This system allows a perfect tightness of the JOSKIN tipping trailers, even with small grains.

The doors of the JOSKIN tipping trailers are fitted with two safety devices:
- In order to prevent system damage, a pressure relief valve regulates the oil pressure if the door cannot be completely closed, e.g. due to an obstacle;
- A safety valve on each door ram holds the door in position if hydraulic hoses break or if the tractor stops.

Safe Tipping

The position of the tipping ram on the front part of the chassis allows to reduce the stresses to the body and makes the vehicle as stable as possible.

Standard mounted on all models of the JOSKIN tipping trailer range, the safety valve, which is directly placed on the tipping ram, prevents the body from unexpectedly falling down (e.g. when hydraulic hoses break).

The double oscillating frame on which the cylinder is mounted allows to compensate the torsions due to the tipping strains and effectively protects the trailer from distortions.

JOSKIN principle

Branking system

In order to adapt your machine in the best possible way to the braking system of your tractors, it is possible to choose between hydraulic, air or dual (hydraulic/air) braking system. The air braking system is part of the standard equipment on triple-axle models and also allows you to choose a proportional system regulating the braking power in proportion to the load.

Tipping stabilizer

The tipping stabilizer with weight transfer system (or its pre-equipment) is standard mounted on Hydro-Tandem and Hydro-Tridem.

On a Roll-Over bogie, two rams are connected to the chassis. When tipping, the circuit will exert a pressure on the rear axle of the bogie in order to lock it in its position and in this way stabilize the tipping trailer.
Models:
Monocoque Tipping Trailers

Pictures

Pictures TRANS-SPACE 1
Pictures TRANS-SPACE 2
Pictures TRANS-SPACE 3
Pictures TRANS-SPACE 4
Pictures TRANS-SPACE 5
Pictures TRANS-SPACE 6
Pictures TRANS-SPACE 7
Pictures TRANS-SPACE 8
Pictures TRANS-SPACE 9
Pictures TRANS-SPACE 10
Pictures TRANS-SPACE 11
Pictures TRANS-SPACE 12
Pictures TRANS-SPACE 13
Pictures TRANS-SPACE 14
Pictures TRANS-SPACE 15

Videos

Videos TRANS-SPACE 1
Videos TRANS-SPACE 2
Videos TRANS-SPACE 3
Videos TRANS-SPACE 4
Videos TRANS-SPACE 5
Videos TRANS-SPACE 6
close
joskin