This website uses cookies to optimize your user experience. By navigating on this website, you consent to this use. To find out more about cookies, consult our privacy policy.
VOLUMETRA Advantage 14 500 l (WPV14502W-01)

VOLUMETRA Advantage 14 500 l

WPV14502W-01

Specificities
  • VOLUMETRA 14,500 l slurry tanker
  • Structure with integrated chassis made of special steel, galvanized inside and outside
  • ADR axles 130 and 406 x 120 mm brakes
  • Wheels 750/60R26.5 (Super Steel Belted BKT) 180 D (Ø 1,574 x 754 mm, 6,750/10,880 kg per wheel at 40 km/h)
  • Hydro-Tandem: hydraulic axle suspension
  • Air brakes in proportion to the load
  • JOSKIN Ø 80 mm 4 t knee-joint eyelet (large plate)
  • 2 LED rear working lights (with control box in the cabin)
  • Wide angle P.T.O.-shaft (1 side) (Walterscheid)
  • W130 volumetric spiral pump (5,000 l/min) - 600 rpm – designed for Ø 8" filling circuit with integrated stone trap
  • Hydraulic device automatically stopping the filling process (DA)
  • Level gauge with float
  • Upper door (Ø 520 mm) with hydraulic opening
  • Pre-equipment for Ø 200 mm not built-in front-JUMBO filling arm (available as an option)
  • Pendislide PRO 150/60PS2 spreading boom with hydraulic folding system
  • SCALPER vertical macerators with 6’’ manual flow control valves, stone trap and HARDOX counterblades
  • Sequence operations at the end of the lines (Automaton)
Download the brochure
More information

  • More information

Volumetra Advantage 16 500 l (WPV16503V-01)

Volumetra Advantage 16 500 l

WPV16503V-01

Specificities
  • VOLUMETRA 16,500 l slurry tanker
  • Structure with integrated chassis made of special steel, galvanized inside and outside
  • ADR axles 150 and 420 x180 mm brakes
  • Self-steering axle with hitching yoke, including quick coupling to the tractor and aligning set-up unit
  • Wheels 710/50R30.5 (Vredestein Flotation TRAC) 173 D (Ø 1,500 x 725 mm, 5,300/8,850 kg per wheel at 40 km/h)
  • Air brakes in proportion to the load
  • JOSKIN Ø 80 mm 3 t knee-joint eyelet (large plate)
  • 2 LED working lights at the back (with control box in the cabin), end outline marker lamps (4 pieces) and LED side marker lights
  • JUROP PNR 155 pump (15,200 l/min at atmospheric pressure - 13,217 l/min at 60% vacuum) - 1,000 rpm - direct connection to the tractor
  • Wide angle P.T.O.-shaft (1 side) (Walterscheid)
  • Hydraulic control of pump change over (DA)
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Ø 6’’ (150 mm) communicating gauge (transparent perspex tube)
  • Pre-equipment for Ø 200 mm not built-in front JUMBO and hydraulic mixer
  • Pre-equipment for rear implements including the linkage, fixing and electrohydraulics with system to execute sequences of operations at the end of lines (Automaton)
Download the brochure
More information

  • More information

Volumetra Advantage 16 500 l (WPV16504V-01)

Volumetra Advantage 16 500 l

WPV16504V-01

Specificities
  • VOLUMETRA 16,500 l slurry tanker
  • Structure with integrated chassis made of special steel, galvanized inside and outside
  • ADR axles 150 and 420 x180 mm brakes
  • Free steering axle
  • Wheels 710/50R26.5 (Alliance A 885) 170 D (Ø 1,400 x 732 mm, 8,160 kg per wheel at 40 km/h)
  • Air brakes in proportion to the load
  • Hydraulic drawbar with closed circuit
  • JOSKIN Ø 50 mm flat eyelet
  • 2 LED working lights at the back (with control box in the cabin) and LED side marker lights
  • JUROP PN 155 pump (15,500 l/min at atmospheric pressure - 13,850 l/min at 60% vacuum) - 1,000 rpm - speed-increasing gearbox
  • Wide angle P.T.O.-shaft (1 side) (Walterscheid)
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Not built-in Ø 200 mm front-JUMBO filling arm
  • Pre-equipment for hydraulic mixer and 500 x 600 mm upper hydraulic access
Download the brochure
More information

  • More information

Volumetra Advantage 18 000 l (WPV18003V-01)

Volumetra Advantage 18 000 l

WPV18003V-01

Specificities
  • VOLUMETRA 18,000 l slurry tanker
  • Structure with integrated chassis made of special steel, galvanized inside and outside
  • ADR axles 150 and 420 x 180 mm brakes
  • Self-steering axle with hitching yoke, including quick coupling to the tractor and aligning set-up unit
  • Wheels 750/60R30.5 (Vredestein Flotation TRAC) 181 D (Ø 1,675 x 785 mm, 6,750/11,200 kg per wheel at 40 km/h)
  • Hydro-Tandem: hydraulic axle suspension
  • Air brakes in proportion to the load
  • JOSKIN Ø 80 mm 4 t knee-joint eyelet (large plate)
  • 2 LED working lights at the back (with control box in the cabin), end outline marker lamps (4 pieces) and LED side marker lights
  • Wide angle P.T.O.-shaft (1 side) (Walterscheid)
  • JUROP PNR 155 pump (15,200 l/min at atmospheric pressure - 13,217 l/min at 60% vacuum) - 1,000 rpm - direct connection to the tractor
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Ø 6’’ (150 mm) communicating gauge (transparent perspex tube)
  • Double feeding of the rear implement (4 m of Ø 8’’ PVC pipe) to reduce the spreading width on the left/right
  • Pre-equipment for Ø 200 mm not built-in front-JUMBO filling arm (available as an option)
  • Pendislide PRO spreading boom with gauge wheels, slope position adjustment and hydraulic folding system
  • SCALPER vertical macerators with 6’’ manual flow control valves, stone trap and HARDOX counterblades
  • System to execute sequences of operations at the end of lines (Automaton)
Download the brochure
More information

  • More information

Tetraliner Advantage 26 000 l (WPTL26006V-01)

Tetraliner Advantage 26 000 l

WPTL26006V-01

Specificities
  • TETRALINER 26,000 l slurry tanker
  • Structure with DOLLY chassis made of special steel, galvanized inside and outside
  • Air suspension
  • BPW 150 axles with 410 x 180 mm brakes
  • Free steering axle with hydraulic locking (DA) and shock absorbers
  • Wheels 560/60R22.5 (Mitas) 161 D (Ø 1,248 x 546 mm, 7,000 kg per wheel at 40 km/h)
  • Air brakes in proportion to the load
  • JOSKIN Ø 80 mm 3 t knee-joint eyelet (small plate)
  • 2 LED rear working lights (with control box in the cabin)
  • Wide angle P.T.O.-shaft (1 side) (Walterscheid)
  • JUROP PNR 155 pump (15,200 l/min at atmospheric pressure - 13,217 l/min at 60% vacuum) - 1,000 rpm - direct connection to the tractor
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Level float gauge and Ø 6’’ (150 mm) communicating gauge
  • Ø 8’’ (200 mm) rear funnel (high position in the middle of the tank)
  • Pre-equipment for Ø 200 mm not built-in front-JUMBO filling arm (available as an option)
  • Pre-equipment for unloading arm
  • Pre-equipment for 500 x 600 m hydraulic access
Download the brochure
More information

  • More information

Modulo XXL Advantage 20 000 l (WPM20001V-01)

Modulo XXL Advantage 20 000 l

WPM20001V-01

Specificities
  • MODULO2 20,000 l slurry tanker
  • Monocoque structure made of special steel, galvanized inside and outside
  • Movable bolted Roll-Over bogie running gear
  • ADR 150 axles with 420 x 180 mm brakes
  • Free steering axle with hydraulic locking (DA) and shock absorbers
  • Wheels 650/65R26.5 Agriterra 02 (Mitas) 174 D (Ø 1,510 x 680 mm, 9,110 kg per wheel at 40 km/h and 4 bar)
  • Hose carrying mudguards
  • Air brakes in proportion to the load
  • Sprung drawbar (parabolic cross leaves) for maximum comfort and driving stability
  • JUROP PNR 155 pump (15,200 l/min at atmospheric pressure - 13,217 l/min at 60% vacuum) - 1,000 rpm - direct connection to the tractor - including: automatic lubrication, Ø 100 mm hoses and JOSKIN Ø 150 mm pressure relief valve
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Self-cleaning syphon (60 l/min)
  • Pre-equipment for hydraulic mixer
  • Pre-equipment for 500 x 600 mm hydraulic access - including pre-equipment for inner and outer ladders
Download the brochure
More information

  • More information

Modulo Advantage 11 000 l (WPM11020V-01)

Modulo Advantage 11 000 l

WPM11020V-01

Specificities
  • MODULO 11,000 l slurry tanker
  • Structure with integrated chassis made of special steel, galvanized inside and outside
  • ADR axle 150 x 2000 and 420 x 180 mm brakes
  • Wheels 800/65R32 Alliance A360 181 A8 (Ø 1,850 mm x 800 mm, 9,900 kg per wheel at 40 km/h)
  • Air brakes in proportion to the load
  • Sprung drawbar (cross leaves) for maximum comfort and driving stability
  • 2 LED working lights at the back (with control box in the cabin), end outline marker lamps (4 pieces) and LED side marker lights
  • JUROP PN 106 pump (11,000 l/min at atmospheric pressure - 10,000 l/min at 60% vacuum) - 1,000 rpm - speed-increasing gearbox
  • Maintenance-free self-cleaning syphon (30 l/min)
  • ECOPUMP: special large volume exhaust pipe with oil collector, high air intake and noise level reduction
  • Ø 6’’ (150 mm) communicating gauge (transparent perspex tube)
  • Pre-equipment for Ø 200 mm not built-in front-JUMBO filling arm (available as an option) and turbo-filler
  • Pendislide BASIC 7.5 m spreading boom with hydraulic folding system
  • SCALPER vertical macerators with 6’’ manual flow control valves, stone trap and HARDOX counterblades
  • System to execute sequences of operations at the end of lines (Automaton)
Download the brochure
More information

  • More information

Tornado Advantage 13 t (WPTO5513-15-01)

Tornado Advantage 13 t

WPTO5513-15-01

Specificities
  • Narrow monocoque body with large wheels, manufactured in special high tensile steel (grade 550) and HARDOX steel (steel sheet for spreading table)
  • Technically permissible payload of 13 t and volume of 14 m³
  • 2K industrial paint and finishing lacquer (total: 100 μ)
  • ADR axle 150 with 420 x 180 mm brakes
  • Wheels 650/75R32 (Mitas AC70G) 172 A8 (Ø 1,795 x 650 mm, 6,300 kg per wheel at 40 km/h)
  • Movable bolted running gear and adjustable bolted drawbar
  • Air brakes
  • Cross-suspension drawbar with parabolic leaves for maximum comfort and stability while driving
  • Reversible and removable teeth in HB400 steel (80 x 12 mm)
  • 1,000 rpm drive by wide-angle Walterscheid P.T.O.-shaft with cam security (beaters rpm: 423 rpm)
  • 2 Ø 16 mm shipping chains with tensioner and interchangeable bolted slats
  • D60 industrial hydraulic installation (1,000 rpm) - flow: 60 l/min
  • Regulation of the moving floor speed according to the tractor speed on Ferti-CONTROL 4000
  • Electronic door opening indicator, spreader counter and moving floor starting safety
  • Protected and retractable lights
  • Anti-projection headboard with grate
Download the brochure
More information

  • More information

TORNADO3 (ADTO5513V/1-01)

TORNADO3

ADTO5513V/1-01

Specificities
  • Narrow monocoque body with large wheels, manufactured in special high tensile steel (grade 550) and HARDOX steel (steel sheet for spreading table)
  • Technically permissible payload of 13 t and volume of 14 m³
  • 2K industrial paint and finishing lacquer (total: 100 μ)
  • ADR axle 150 with 420 x 180 mm brakes
  • Wheels 650/75R32 (Mitas AC70G) 172 A8 (Ø 1,795 x 650 mm, 6,300 kg per wheel at 40 km/h)
  • Movable bolted running gear and adjustable bolted drawbar
  • Cross-suspension drawbar with parabolic leaves for maximum comfort and stability while driving.
  • Air brakes
  • Reversible and removable teeth in HB400 steel (80 x 12 mm)
  • 1,000 rpm drive by wide-angle Walterscheid P.T.O.-shaft with cam security (beaters rpm: 445 rpm)
  • 2 Ø 16 mm shipping chains with tensioner and interchangeable bolted slats
  • Ferti-CONTROL 300 control box – including the electric moving floor control with flow regulator, floor on/off switch and inversion of the moving floor direction
  • End outline marker lamps (4 pieces) and LED side marker lights
  • Anti-projection headboard with grate
  • Guillotine door
Download the brochure
More information

  • More information

Trans-CAP Advantage 18 t (WPTC6532-01)

Trans-CAP Advantage 18 t

WPTC6532-01

Specificities
  • Tapered monocoque body in 4 mm high tensile steel (grade 420; side walls and floor)
  • Body dimensions: 6.39 m - 6.73 m long; 2.18 m - 2.26 m wide; 1.50 m high
  • Technically permissible payload of 18 t and volume of 21.90 m³ DIN
  • 1-part hydraulic rear door (DA) with hydraulic arm integrated in the arm, 500 x 500 mm grain chute and seal
  • 4 front sight windows with perspex closing plate (width: 21 cm; height: 63 cm) with rods
  • 900 mm chassis made of 300 x 100 x 8 mm steel sections
  • 2K industrial paint and finishing lacquer (total: 100 μ)
  • Roll-Over bogie movable bolted running gear
  • ADR axles 130 and 406 x 120 mm brakes
  • Free steering axle with shock absorbers and hydraulic locking system (DA)
  • Wheels 600/55R26.5 (Mitas Agriterra 02) 165 D (Ø 1,335 x 626 mm, 7,000 kg per wheel at 40 km/h)
  • Air brakes in proportion to the load
  • Sprung drawbar (parabolic cross leaves) for maximum comfort and driving stability
  • Hydraulic parking stand
  • Oil-fed tipping: 33 l hydraulic ram on double oscillating frame
  • Pre-equipment for tipping stabilizer, cover and front platform
Download the brochure
More information

  • More information

Trans-SPACE Advantage 26 t (WPTS8015-01)

Trans-SPACE Advantage 26 t

WPTS8015-01

Specificities
  • Tapered monocoque body in HARDOX 400 (floor) and 4 mm special high tensile steel (grade 420; side walls)
  • Body dimensions: 8.08 m - 8.41 m long; 2.18 m - 2.26 m wide; 1.50 m high
  • Technically permissible payload of 26 t and volume of 27.4 m³ DIN
  • 1-part hydraulic rear door (DA) with 500 x 500 mm central grain chute and seal
  • Large front sight window with galvanized rods and transparent perspex plate (177 x 76 cm)
  • 900 mm chassis made of 300 x 100 x 10 mm steel sections
  • Primer Ester Epoxy 2K industrial painting and finishing lacquer (total: 100 μ)
  • ADR axles 150 and 420 x 180 mm brakes
  • Double self-steering system (first and last axles) with hitch yoke, including quick coupling to the tractor and aligning set-up unit
  • Front lifting axle
  • Wheels 650/55R26.5 (Alliance 885 SB) 170 D (Ø 1,380 x 648 mm, 8,160 kg per wheel at 40 km/h)
  • Hydro-Tridem: hydraulic suspension
  • Air brakes in proportion to the load
  • Sprung drawbar (parabolic cross leaves) for maximum comfort and driving stability
  • JOSKIN Ø 80 mm 3 t knee-joint eyelet (large plate)
  • 150 l/min industrial hydraulic pump with electric tipping and lowering controls
  • Galvanized front ladder
  • Pre-equipment for cover, front and rear platforms
Download the brochure
More information

  • More information

Trans-KTP Advantage 22 t (WPTK2250-06)

Trans-KTP Advantage 22 t

WPTK2250-06

Specificities
  • Tapered monocoque body in 6 mm HARDOX 450 steel (side walls and floor); reinforced upper strip
  • Body dimensions: 5.06 m - 5.28 m long; 2.18 m - 2.26 m wide; 0.95 m high
  • Technically permissible payload of 22 t and volume of 10.90 m³ DIN
  • 900 mm chassis made of 300 x 150 x 8 mm steel sections
  • 2K industrial paint and finishing lacquer (total: 100 μ)
  • 1-part hydraulic rear door with wide opening angle (protected hydraulic rams)
  • BPW 150 x 1,950 axles with 410 x 180 mm brakes
  • Wheels 650/55R26.5 (Alliance) 167 E TL 380 (Ø 1,360 x 645 mm, 6,000/7,900 kg per wheel at 40 km/h)
  • Movable bolted running gear and adjustable bolted drawbar
  • Air brakes in proportion to the load
  • Cross-suspension drawbar with parabolic leaves for maximum comfort and stability while driving
  • JOSKIN Ø 80 mm 3 t knee-joint eyelet
  • Oil-fed tipping: 36 l hydraulic ram on double oscillating frame
  • Galvanized front ladder and headboard
  • Hydraulically retractable rear bumper
  • Thermoplastic mudguards
  • Hydraulic skid
Download the brochure
More information

  • More information

Trans-KTP Advantage 27 t (WPTK2765-03)

Trans-KTP Advantage 27 t

WPTK2765-03

Specificities
  • Tapered monocoque body in 6 mm HARDOX 450 steel (side walls and floor); reinforced upper strip
  • Body dimensions: 6.49 m - 6.70 m long; 2.18 m - 2.26 m wide; 0.95 m high
  • Technically permissible payload of 27 t and volume of 13.9 m³ DIN
  • 1-part hydraulic rear door with wide opening angle (protected hydraulic rams)
  • Narrow chassis (700 mm) in 300 x 150 x 10 mm steel sections for a 2.55 m total width; 64 l hydraulic tipping ram
  • 2K industrial paint and finishing lacquer (total: 100 μ)
  • BPW axles 150 mm with 410 x 180 mm brakes
  • Double self-steering system (first and last axles) with hitch yoke, including quick coupling to the tractor and aligning set-up unit
  • Front lifting axle (DA)
  • Wheels 650/55R26.5 TL (Nokian CT BAS) 177 D (Ø 1,389 x 645 mm, 9,950 kg per wheel at 40 km/h)
  • Hydro-Pendul: hydraulic axle suspension with knee-joints and slope position adjustment
  • Air brakes in proportion to the load
  • Hydropneumatic drawbar (DA) with automatic height adjustment
  • JOSKIN Ø 80 mm 4 t knee-joint eyelet (large plate)
  • Tipping by 150 l/min industrial hydraulic pump (1,000 rpm) with tipping stabilizer with electric control
  • Electrohydraulic control of the machine (hydraulic door, hydropneumatic drawbar, front lifting axle)
  • Galvanized front ladder and headboard
  • Pre-equipment for automatic lubrication (61 greasing nipples)
Download the brochure
More information

  • More information

Drakkar Advantage 48,8 m³ (WPDR8603-01)

Drakkar Advantage 48,8 m³

WPDR8603-01

Specificities
  • Tapered body with steel posts, and side walls with UV-resistant Polyfont panels
  • Body dimensions: 8.30 m - 8.70 m long; 2.38 m wide; 1.50 m high
  • Technically permissible payload of 28 t and volume of 48.8 m³ DIN
  • Hydraulic rear door with 3 grain chutes (600 x 270 mm)
  • Mobile sloping front wall with steel posts and perspex closing plate
  • Conveyor belt driven by 2 hydraulic motors with unloading assistance to prevent any stretching of the conveyor belt
  • BPW axles 150 and 410 x 180 mm brakes
  • Double self-steering system (first and last axles) with hitch yoke, including quick coupling to the tractor and aligning set-up unit
  • Front lifting axle
  • Wheels 650/55R26.5 (Agriterra 02 MITAS) 169 D (Ø 1,389 x 645 mm, 7,890 kg per wheel at 40 km/h)
  • Hydro-Tridem: hydraulic axle suspension with automatic height adjustment
  • Air brakes in proportion to the load
  • Hydropneumatic drawbar
  • Unloading controls in the cab and at the back of the vehicle
  • Fully electrohydraulic management of the machine (compatible with load sensing)
  • Non-hermetic galvanized steel extensions with manual adjustment on 4 positions (0 / 250 / 400 / 500 mm) to increase the body volume up to 48.8 m³ or 53 m³ with dome for material with low density
Download the brochure
More information

  • More information

Scariflex Advantage 9,6 m (WPSCA960-01)

Scariflex Advantage 9,6 m

WPSCA960-01

Specificities
  • Large working width (9.6 m)
  • 5-section chassis (1.20 m + 2.40 m + 2.40 m + 2.40 m + 1.20 m) with double hydraulic folding system
  • Structure and tools fully made of galvanized special steel. Shot-blasted and then painted (2K) blades in treated steel
  • 6 rows of tools for an intensive and precise work:
    • 1 row of 60 cm leveling scrapers on half-flexible leaves;
    • 5 rows of spring tines (Ø 8 mm).
  • Independent adjustment of the work intensity of every tool:
    • with the gauge wheels (scrapers);
    • with a lever on the rows of flexible tines so as to have the same angle on all elements.
  • Flexible hitch to follow the ground relief perfectly and limit vibrations
  • Automatic locking in transport position (mechanical unlocking by means of a cord from the cabin)
  • 2 pairs of rubber wheels (Ø 375 x 150 mm)
  • DELIMBE 300 l air seeder: turbine with hydraulic drive, control box and “highflow” distributor (recommended for grass, grains and vetches)
  • Compatible with 120-hp tractors or more
Download the brochure
More information

  • More information

Scariflex Advantage 6 m (WPSCA600/1-01)

Scariflex Advantage 6 m

WPSCA600/1-01

Specificities
  • Large working width (6 m)
  • Chassis made of 3 sections (1.80 m + 2.40 m + 1.80 m) with hydraulic folding system
  • Structure and tools fully made of galvanized special steel. Shot-blasted and then painted (2K) blades in treated steel
  • 6 rows of tools for an intensive and precise work:
    • 1 row of 60 cm leveling scrapers on half-flexible leaves
    • 5 rows of spring tines (Ø 8 mm)
  • Independent adjustment of the work intensity of every type of tool:
    • with the gauge wheels (scrapers)
    • with a lever on the rows of flexible tines so as to have the same angle on all elements
  • Flexible hitch to follow the ground relief perfectly and limit vibrations
  • Automatic locking in transport position
  • 2 pairs of rubber wheels (Ø 375 x 150 mm)
  • Compatible with 60-hp tractors or more
Download the brochure
More information

  • More information

With the “Advantage” concept, JOSKIN wanted to prove that it was possible to reduce the price of agricultural machines without having an impact on quality. To get rid of this budget constraint, JOSKIN bet everything on a “mass” production that was until then not used in the agricultural trailer sector. The concerned models are indeed assembled on dedicated assembly lines so as to produce identical series of machines. Producing a large quantity of a model implies more advantageous prices for the raw materials, a more profitable distribution of the workforce and a higher efficiency of the automated industrial machines. The resulting savings have then a direct impact on the sale price and allow to deliver a high-tech product at the price of a standard one.

×