Finalising your subscription
To validate your subscription, please enter the 6-digit code that we have just sent you by e-mail.
X
![Finalising your subscription]()
For gentle spreading.
With 1" valve (for closure during transport), in rear or side position.
over the entire length of the tank (except Aquatrans XL).
Equipped with a mechanism connected to a feeding valve.
Protected level indicator, out of reach of animals.
Ø 450 mm lid with quick opening and seal.
2" 1/2 rear ball valve for fast, precise dosing.
For access to Ø 450 mm door with water filling hose
Of 3.5 m or 4.5 m long.
At the 2 rear ends for cleaning.
With rear (folded over each other against the door) or side storage, expendable from 2.3 m to 3.7 m.
For tying up the cattle, at 75 and 115 cm high.
At 90°, 115°, 130° or 265°.
Dimensions meeting European standards
(A) Floor in 3/5 chequered plate, side walls in QSTE 420 steel (thickness: 4 mm).
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
Of 3.5 m (A) or 4.5 m (B) long.
With locking at intervals of 640 to 980 mm depending on the model, suitable for small and large animals. Door opening from inside or outside.
That can be opened to different positions, with a 270° rotation.
To allow air to circulate (ideal for transport in hot weather conditions).
That can be positioned anywhere thanks to a flexible fixing system.
Dimensions meeting European standards
With double flexible shock-absorbing security to protect the P.T.O.-shaft and the tractor
When pulling out.
For the telescopic arm.
Kinematics: loading (A) of the container via a central articulation and tipping (B) via an articulation at the rear (locking of the central articulation during tipping).
Telescopic arm (C) (1 to 1.2 m depending on the model) to adapt to different container lengths and increase the pullout force
For clean installation and better oil circulation.
Arm locking via positioning rails.
(1 to 1.2 m depending on the model) to adapt to different container lengths and increase the pullout force
Which pushes the arm vertically, making it easier to lift off (D18, D22, T22 and T30). Pre‑equipmenton D14.
For a greater resistance to pressure.
3 basic drop side heights 5 possible combinations!
For the lighting, braking and tipping system of a second trailer with swivel rear hitch.
With individualised spare parts book.
On all models (thickness: 4 mm).
For an efficient emptying of silage.
To see inside the body.
(opening: 390x300 mm) with automatic locking.
Along the entire length and height.
Avant pour faciliter la manipulation des ridelles (uniquement sur modèles 4525 et 5025).
All around the body for a perfect tightness.
(440x240 mm) with storage under the body.
(A) Ø 50 mm swivel eye
(B) Ø 80 mm knee-joint eyelet
(C) Ø 50 mm fixed eyelet (standard)
(D) Ø 40 mm fixed eyelet
With direct connection to the tractor on Delta-SPACE.
With 2x6 fasteners for a perfect strength
4 layers of fabric and PVC with nylon structure.
Belt and front wall driven by a reel at the rear of the machine and 2 powerful hydraulic motors.
• Ø 844 to 1,247 mm
• Width: 297 to 611 mm
And many more!
No suction cup effect to allow the belt to slide along without unnecessary traction.
For a smooth, even unloading.
And belt return (cab, rear left and right).
From a set pressure to distribute forces over the entire conveyor belt.
To the rear of the body: no compaction of goods, continuous unloading, no pressure on the side walls, no residues...
Without macerator - Manual folding system - Couping directly to the Ø 150 mm outlet of the slurry tanker.
With 4 blades.
in continuous spirals on Ø 219 mm tube.
Height of the spreading unit: 1,770 mm (series 11), 2,220 mm (series 14)
Clearance height under guillotine door: 1,355 mm (series 11), 1,700 mm (series 14).
Aluminium or wood.
Reversible, twisted HARDOX 450 beater knives for good spreading.
– stainless steel inner plate
– quick assembly on spreading unit.
For improved paint finish under the body and easy replacement.
Galvanised guillotine door reinforced with numerous ribs. Double reinforcement on the lower part.
• Ø 1,080 to 1,505 mm
• Width: 390 to 750 mm
And many more!
Right, left or both sides
In galvanised steel.
To see inside the body.
HARDOX protection wear plates.
For use with the canopy.
For hydraulic and electrical lines.
At man’s height.
For high capacity, with reinforcing folds along the entire length of the side walls and reinforced upper body edges for improved side wall strength.
that can be adjusted in 3 positions depending on the desired width and the material to be spread. Blades protected by 2-position safety bolts. Use of 4 blades instead of 6 possible.
On a Ø 140 mm tube, with HARDOX steel teeth.
For easy deterioration of the strings and cleaning.
On a Ø 140 mm tube, with HARDOX steel teeth. Only on Ferti-SPACE2 FS7014 and FS8014 models.
Oversized beater bearings protected against manure.
For use of compost, easy cleaning or fast unloading.
With more or less ventilation, by means of an adjustable board via two cranks.
To protect the canopy against material return.
For a higher spreading precision.
On the inside of the canopy to prevent manure from sticking.
In 12 mm HARDOX steel, designed to facilitate the downward projection onto the discs.
With spare part numbers.
(A) Structure made of steel of sheet metal profiled tubes.
(B) Core penetration of zinc in steel at 450°C.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
From the centre to each side for perfectly even spreading
(A) 2 stands retracting in the frame.
(B) Stabilising 3rd point for safe storage.
With flow control.
With two hydraulic 3rd points on Penditwist from 15 m and Pendislide PRO.
To limit space requirements on the slurry tanker and leave room for other options at the front of the tank (e.g. side filling arm).
To ensure a high flow with vacuum pump + 2 manually-adjustable (standard) or hydraulically-adjustable* (optional) valves.
*Ramus anti-clog valves, with electric sensor for independent flow adjustment for each macerator.
(Ø 125 mm – industrial type) connected to the macerator by a curved elbow for a very regular flow.
• floating position of the 2 wing cylinders: adaptation to the transverse profile under each wing,
• 4-cylinder anti-drip system: floating position during spreading for optimal follow‑up of the ground relief.
Row spacing on Pendislide PRO: 25 cm.
Row spacing on Penditwist: 25 or 30 cm (depending on the model).
With exact scatterer or for slurry transfer.
For direct in-line spreading on the ground.
To ensure even pressure of all elements on the ground.
(A) Lightened structure made of profiled tubes in high tensile steel.
(B) Core penetration of zinc in steel at 450°C.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
For direct in-line spreading on the ground.
To transfer as much weight as possible to the slurry tanker during travel.
(A) Leaf protection stop.
(B) Spring-steel leaf.
(C) Steel counter-stop to prevent rocking when driving.
To ensure even pressure of all elements on the ground.
For greater fluidity.
(A) Lightened structure made of profiled tubes in high tensile steel.
(B) Core penetration of zinc in steel at 450°C.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
For direct in-line spreading on the ground.
To transfer as much weight as possible to the slurry tanker during travel.
(A) Leaf protection stop.
(B) Spring-steel leaf.
(C) Steel counter-stop to prevent rocking when driving.
(5 parts) to limit height on the road.
To improve and regulate the pressure of the boom on the shares.
At the macerator entrance.
Mounted on very flexible spring leaves on R5S3.
With adjustable angle of attack on R6D2S3.
Mounted on semi-flexible spring leaves on R6D2S3, R6S5 and R5S3
With graduation and marking arrow.
For a good follow-up of the ground.
Of variable width (90 to 130 cm) depending on model, positioned in front of the wheels to level the ground.
Coupled with an articulated hitch and a spring-loaded 3rd point for a smooth follow-up of the ground.
For a good stability when unhitching.
To make them puncture-proof.
For a good stability on the road (models: 7.2 to 12 m).
Built into the chassis to limit the width on the road and maximise the inside body width.
To eliminate vibration and protect the bearings.
To the galvanised chassis.
To ensure the machine longevity.
Under the moving floor chain.
Self-lubricating, noise-reducing Ertalon rails inside and under the body.
Moving floor with closed tube slats and 4 yaw chains, driven by 2 hydraulic motors.
With or without shredding beaters. Clear rear of the machine to prevent material build-up.
With tension indicator (Belleville washers).
With numerous positions for storing the hoses.
Inside widths on all models: 2,340 mm at the front and 2,380 mm at the rearfor decompaction when unloading.
2 Ø 820 mm (S4008) or 900 mm vertical beaters, 423 rpm, with 10 mm thick spiral welded to tubes with a diameter of 140 mm (S4008) or 190 mm for other models.
(A) Upper beater lubrication within reach.
(B) Galvanised cord cutter.
Aluminium or wooden 250 mm extensions.
Reversible, twisted HARDOX 450 beater knives for good spreading.
Bolted galvanised floor for easy replacement in case of wear.
To view the inside of the body.
Protected by a cover with two compensating cylinders.
With sight window integrated to the body.
(A) High tensile steel.
(B) Core penetration of zinc in steel at 450°C.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
Incompatible with SIROKO S4008/8V.
Very sturdy galvanised ribbed guillotine door, with additional reinforcement at the basis.
• Ø 1,080 to 1,795 mm
• Width: 390 to 697 mm
And many more!
Right, left or both sides.
Made of 4 mm sheet metal (S420MC) with reinforcement folds over the entire length.
(width: 6.5 cm)
Slurry feeding hose
with height adjustment by means of a crank and position ruler (only available on Terraflex/2 and /2XXL).
For deeper work behind tractor wheels.
(A) 8 to 12 mm steel thickness depending on model.
(B) Core penetration of zinc in steel (450°C) from both inside and outside the tube.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
(Ø 605 x 210 mm) with adjustment by crank with height indicator (A).
For good crop residue clearance.
(width: 24 cm) with bolt security.
Slurry feeding hose.
For smooth, clog-free slurry flow.
Instead of swivel rear hitch.
For the lighting, braking and tipping system of a second trailer with swivel rear hitch.
Tetra-CAP/SPACE: 250x100 or 300x100 mm (section A) and 150x150 mm (section B)
To see inside the body.
Connecting the drawbar to the axle leaf bundle on Tetra-CAP/SPACE.
along the entire length and height.
Ø 1,010 mm with continuous spiral on 219 mm tube: 423 rpm with a 1,000-rpm P.T.O. shaft drive.
(A) Beater lubrication within reach.
(B) Galvanised cord cutter
Aluminium or wood.
Reversible, twisted HARDOX 450 beater knives for good spreading.
For field edges and safety on the road.
Galvanised guillotine door reinforced with numerous ribs. Double reinforcement on the lower part.
• Ø 1,080 to 2,060 mm
• Width: 390 to 716 mm
And many more!
Left or right.
(A) Body and side walls in QSTE 420 steel (thickness: 4 mm).
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
For right- and left-hand beater.
Manually removable single canopy.
320 rpm, with HARDOX steel teeth.
For use of compost, easy cleaning or fast unloading.
With twisted profile: better crankcase ventilation and more uniform distribution (on TR-ATR-TRT-BEV).
to prevent mechanical damage to the machine.
144 mm wide galvanised skids over the entire depth of the machines. Mowing height adjustable over 6 to 8 positions, depending on model.
Standard on ATR and ABJ.
540 rpm
1,000 rpm
Standard on TRT, DTH3, BEV, BJ and ABJ.
With telescopic cylinder on a double oscillating frame placed in an advanced position in the chassis.
(250 or 500 mm) stackable up to 1 m.
While complying with the regulations.
(250 mm) stackable up to 1 m.
Models 5500, 6000 and 6500.
On models 5500, 6000 and 6500.
On models 6000 and 6500.
On models 4500 and 5000.
(500 or 750 mm), only combinable with 250 mm extensions.
For easy unloading of material.
With closing force arms and 3 clamping hooks for good watertightness.
With high tensile steel hinges and triple lock for good watertightness. 270° door opening and side locking possible.
For a sturdy base and perfect watertightness.
For a precise adjustment along the entire length of the body.
To prevent material build-up.
On basic drop sides designed to add extensions.
To secure drop sides.
closed at the top for strength along the entire length, and multiposition hinges at the bottom.
Rear door, side and front panels.
(standard preequipment).
100% secure in closed position and lockable in open position.Rubber handle.
To prevent material build-up and protect the upper body edge.
Welded on models 17/22/27, bolted on 24/31/34.
Stackable up to 1 m.
(incompatible with some configurations): upper body edge strip (2 side walls + rear door).
(A) Body in 5 mm (Trans-KTP 17) or 6 mm (Trans-KTP 22/24/27/31/34) thick HARDOX 450.
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
Allowing the fitting of wide wheels while complying with the regulations and optimising sturdiness and the empty weight.
For easier unloading of material.
Stackable up to 1 m.
Incompatible with some configurations: upper body edge strip (2 side walls + rear door).
(A) Side walls and floor in 4 mm (Trans-KTP 9 and 11) or 5 mm (Trans-KTP 15 and 17) thick HARDOX 450 steel.
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
With 2-part door.
while complying with the regulations and optimising sturdiness and the empty weight.
For total clearance.
Attached close to the axles to facilitate traction.
With fastening as close as possible to the axles to provide a natural traction line and reduce the power requirements.
For easier unloading of material.
For tractors with insufficient oil capacity. Hydraulic lowering control possible.
(1x250 mm or 2x250 mm).
with the cylinder in a forward position in the chassis to reduce the stress level.
(A) Side walls and floor in 4 mm thick high tensile steel.
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
while complying with the regulations.
(2.18 m at the front and 2.26 m at the rear) to facilitate unloading.
On a double-oscillating frame with greased bearings.
For Roll-Over bogie.
For an easier use.
(Depending on the model) with telescopic cylinder on a double oscillating frame (A) placed in an advanced position in the chassis.
(250 or 500 mm) stackable up to 1 m.
(A) Body side walls in S550 steel and floor in HARDOX 450.
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
While complying with the regulations and optimising sturdiness and the empty weight.
For greater stability on dangerous terrain + protection for reversing lights.
(500 or 750 mm), only combinable with 250 mm extensions.
For easy unloading with the material sliding.
(A) 9.6 m + 2.1 m = 11.7 m
(B) 10 m + 1.1 m hydraulic extension = 11.1 m
(C) 9.6 m + 0.4 m = 10 m
(D) Adjustable tandem position for 10 and 12 m trailers
Removable, multiposition
(A) Floor in folded high tensile steel sheet (thickness: 4 mm).
(B) Core penetration of zinc in steel at 450°C.
(C) 70-micron galvanising with special treatment before and after immersion in the zinc bath.
Of the chassis on trailed WAGO.
(A) Floor in chequered plate with a 2.5 cm edge to better hold the load.
(B) Automatic shot-blasting with 20 turbines (2,300 kg shot/min).
(C) 2K primer coat applied directly after blasting + flash-off before applying the finish.
(D) 2K topcoat with accelerated drying at 60°C.
With front and rear supports (only available on 8 m and 10 m models, including on WAGO-Loader with manual ramps or telescopic ramp).
To automatically secure the upper bales whatever their height (70 to 120 cm) • Patented system.
Resting on the floor.
On all WAGO-Loader low loaders.
On all WAGO-Loader low loaders.
